Technology of laying gypsum tiles with your hands

Gypsum tiles have to be laid properly, as not just the aesthetic appearance of decorative facing, but also the service quality of

the material will be based on the technologies of job. The product is universal, and it may be attached to concrete, plaster,

brick or gypsum board sheets, and provided that the surface of the base is even and has no defects.

In the event the defects of this base are important, it should be completely treated with primer, and then a cement mortar is

made, which fills all of the cracks. Then the surface should be primed and dried. In cases like this, its composition should

select a special, containing elements that prevent the appearance of fungus and mold.

In today’s interior of these rooms most often used gypsum tiles, imitating natural brick or stone. To carry out decorative

finishing yourself, it’s essential first of all to select a scheme of tile placement and prepare a solution. It is crucial to look

closely at the reverse side of this material. When its surface has an embossed surface, then the adhesive ought to be placed

having an even trowel, also if it is even, then using a top notch one.

The technology of this work is as follows:

* A thin coating of adhesive mortar is put on the pre-prepared wall. It’s distributed over the bottom so it is likely to put 4-5

tiles. Decorative cladding may be placed either on plasterboard, and on putty.

* Glue the rear side of the tiles with glue.

* Plaster elements are pressed against the walls and their place is adjusted. To align the seams, it’s recommended to use

spacers.

* Finishing is performed in rows, each of which should be changed by half a tile masterfasada.ru. Facing is carried out into the corners of the

room, and then immediately eliminate any residual mortar at the joints.

Drying the walls requires no longer than a day and requires a constant humidity and temperature in the room. The final stage in

the placing of gypsum tiles is their own decoration. To do this, the joints between the components are full of a particular

solution, the color of which matches the brick.

Decorative imitation of brickwork on the walls has been carried out in the following ways:

* Cutting the surface of the stitches of masonry using a bolt cutter along with your hands;

* laying of tiles beneath the brick:

* mimicking the structure and colour of the side of one brick;

* Imitating a fragment of brickwork of several bricks.

The perfect method to decorate”beneath the brick” is the one that permits you to create a functional coating together with the

maximum appearance of its resemblance to natural masonry. All 3 methods to carry out this type of finishing functions meet the

requirements, but the cutting edge of joints using a bolt is more labor-intensive along with the creation of large amounts of

dust, so let us consider more common ways.

The old finish is removed from the walls, and the surface, if needed, is leveled to eliminate the need to paste plaster onto a

thick layer of adhesive.

Combining such cladding with different kinds of interior finishes could be both orderly and done with no clear consistency,

chaotically, together with fake of signs of aging.

With the support of cosmetic gypsum tiles it is possible to imitate a large number of textures.

A large number of textures can be imitated with the support of cosmetic gypsum tiles.

The wall where it is to be set up should have the following characteristics:

* Hardness and intensity of the outside;

* The lack of irregular places and sharp gaps;

* no deformations.

Decorative tiles in the interior of this kitchen

Walls are made from a number of substances, so let’s break down the individual rules of setup.

When dealing with concrete, there’ll not be any huge problems. It’s simply essential to take into consideration the porosity of

the material. Concrete, that has practically no pronounced pores, ought to be treated with a good primer.

Mounting gypsum tiles concrete

Before beginning work on the installation of gypsum tiles on the walls, it’s worth assessing the strength of their surface. When

the plaster doesn’t fall off the walls and at exactly the same time holds well, you can simply paint it with primer.

Mount the tiles onto the painted concrete should not. The surface should be scratched, ensuring to misfire, then it ought to be

grouted and covered with a layer of plaster.